background image

6

ment will be used when installing the cutting blade.

Install the Cutting Blade

4.

Place the cutting blade on the output shaft bushing (Fig. 10).

5.

Make sure that the cutting blade is centered on the pilot step
and sitting flat against the output shaft bushing (Fig. 11).

6.

Align the shaft bushing hole with the locking rod slot and
insert the locking rod into the bushing hole (Fig. 7).

7.

Put the blade retainer and nut on the output shaft. Make
sure that the blade is installed correctly. 

8.

Tighten nut counterclockwise against the blade while
holding the locking rod:

• If using a torque wrench and an 13 mm socket, tighten to:

37 - 38 N•m, 325 - 335 in•lb, 27 - 28 ft.•lb.

• Without a torque wrench, use a 13 mm closed-end or

socket wrench, turning the nut until the blade retainer is
snug against the shaft bushing. Make sure that the blade is
installed correctly, then rotate the nut an additional 1/4 to
1/2 turn counterclockwise (Fig. 12).

9.

Remove the locking rod from the locking rod slot.

REMOVE THE CUTTING BLADE AND INSTALL THE CUTTING
ATTACHMENT

Remove the Cutting Blade

1.

Align the shaft bushing hole with the locking rod slot and
insert the locking rod into the bushing hole (Fig. 7).

2.

Hold the locking rod in place by grasping it next to the
boom of the unit (Fig. 13).

3.

While holding the locking rod, loosen the nut on the blade
by turning it clockwise with a
13 mm closed-end or socket
wrench (Fig. 13). 

4.

Remove the nut, blade
retainer and blade. Store the
nut and blade together for
future use in a secure place.
Store out of children’s reach.

Install the Cutting Attachment

5.

Align the shaft bushing hole
with the locking rod slot and insert the locking rod into the
shaft bushing hole (Fig. 7). Place the blade retainer on the
output shaft with the flat surface against the output shaft
bushing as shown in Fig. 14. Screw the cutting attachment
counterclockwise onto the output shaft. Tighten securely.

NOTE:  

The blade retainer must be installed on the output

shaft in the position shown for the cutting attachment
to work correctly.

6.

Remove the locking rod.

7.

Install the cutting attachment shield. Refer to 

Remove and

Install the Cutting Attachment Shield.

ASSEMBLY INSTRUCTIONS

WARNING: 

Do not sharpen the cutting blade.

Sharpening the blade can cause the blade tip to break
off while in use. This can result in severe personal
injury. Replace the blade.

Shield

Mount

Locking Rod

Cutting

Blade

Blade Retainer

Nut

Output Shaft

Bushing

Pilot Hole

Fig. 10

WARNING: 

If the cutting blade is off-center, the

unit will vibrate and the blade may fly off, causing
possible serious personal injury.

Pilot Step

Fig. 11

1/4-1/2 turn

Counterclockwise

Fig. 12

Clockwise

Fig. 13

Cutting Attachment

Locking Rod

Blade Retainer

Output Shaft

Bushing

Fig. 14

WARNING: 

To avoid serious personal injury or

damage to the unit, do not start or operate this unit
with the locking rod in the locking rod slot.

WARNING: 

To avoid serious personal injury,

always wear gloves while handling or installing the
blade.

Summary of Contents for Y780

























































Reviews: