background image

14

SECTION 8:  MAINTAINING YOUR LAWN MOWER

General Recommendations

Always observe safety rules when performing any 
maintenance.

The warranty on this lawn mower does not cover 
items that have been subjected to operator abuse 
or negligence. To receive full value from the 
warranty, operator must maintain the lawn mower 
as instructed in this manual. 

Changing of engine governed speed will void 
engine warranty. 

Some adjustments will have to be made 
periodically to maintain your unit properly. All 
adjustments in the Making Adjustments section of 
this manual should be checked at least once each 
season. 

Periodically check all fasteners and make sure 
these are tight.

Follow the maintenance schedule under Customer 
Responsibilities to get quality performance from 
your lawn mower.

Lubrication

Always stop engine and disconnect spark 
plug wire before cleaning, lubricating or 
doing any kind of service work on the lawn 
mower.

Blade Control: Lubricate the pivot points on the blade 
control handle at least once a season with light oil. The 
blade control must operate freely in both directions. 
See Figure 17.

Wheels: Lubricate the wheels at least once a season 
with light oil (or motor oil). If the wheels are removed for 
any reason, lubricate the surface of the axle bolt and 
inner surface of the wheel with light oil. See Figure 17.

Engine: Follow the separate engine manual packed 
with you unit for lubrication instructions.

Figure 17

Customer Responsibilities

MAINTENANCE 

SCHEDULE

P

R

O

D

U

C

T

E

N

G

IN

E

SERVICE 

DATES

A

fte

e

ac

u

se

E

ve

ry

 2

h

ou

rs

E

ve

ry

 5

ho

u

rs

B

ef

or

st

or

ag

e

E

ve

ry

 1

00

 h

ou

rs

O

nc

se

a

so

n

Lubricate wheels

Clean deck

Blade care

Change oil

Clean engine

Replace air filter

Check spark plug

Check spark arrester (if any)

Lubricate blade control

Lubricate

Summary of Contents for 509 Series





















Reviews: