Yanmar 6LPA-STP2 Operation Manual Download Page 75

Page: 75 / 110

Every 1250 Hours of Operation

Perform the following maintenance

procedures every 1250 hours of operation

or 5 years, whichever comes first.

• Cleaning the Cooling Water System
• Cleaning and Checking the Seawater

Passage

• Cleaning and Checking the Fresh

Water Cooling Water Passage

• Adjusting the Tension of the

Alternator V-Belt

• Replacing the Timing Belt
• Washing Engine Oil Cooler
• Replacing the Front Rubber Damper

Cleaning the Cooling Water System

See your authorized Yanmar Marine dealer

or distributor.

Cleaning and Checking the

Seawater Passage

See your authorized Yanmar Marine dealer

or distributor.

Cleaning and Checking the Fresh

Water Cooling Water Passage

See your authorized Yanmar Marine dealer

or distributor.

Adjusting the Tension of the

Alternator V-Belt

See Checking and Adjusting the Alternator

V-Belt Tension on page 67.

Replacing the Timing Belt

See your authorized Yanmar Marine dealer

or distributor.

Washing the Engine Cooler

See your authorized Yanmar Marine dealer

or distributor.

Replacing the Front Rubber Damper

See your authorized Yanmar Marine dealer

or distributor.

PERIODIC MAINTENANCE

6LPA Series Operation Manual

Summary of Contents for 6LPA-STP2















































































































Search results

Summary of Contents for 6LPA-STP2

Reviews:

Brands by name

Popular brands

Yanmar 6LPA-STP2, Operation Manual

Search results

Summary of Contents for 6LPA-STP2

Reviews:

Brands by name

Popular brands