manualshive.com logo in svg

Yanmar 6LPA-STP2, Operation Manual

Share
Download
Yanmar 6LPA-STP2 Operation Manual Download Page 25

Switches and Gauges

Switch or Gauge

Function

0003622

(1)

(2)

(3)

(4)

Starter (Key) Switch

OFF (2): The key can be inserted or removed from switch. All

power is turned off. 

*

ON (3): For engine operation. Gauges and alarms are

operational.

START (4): For starting engine. When key is released after

engine starts, key automatically moves to ON position. NOTICE:

NEVER hold the key in the START position for longer than

15 seconds or the starter motor will overheat.

GLOW (1): For air heater (optional).

Engine Stop Button

Press the button to stop the engine by cutting off the fuel flow.

Continue to press the button until the engine has stopped. 

**

Warning Alarm (Buzzer)

The alarm sounds if an abnormality is detected. See Warning

Devices on page 20.

Warning Indicators

The lamps illuminate when an abnormality is detected. See

Warning Devices on page 20.

Alarm (Buzzer) Stop Switch

The switch is used to shut the alarm off temporarily. Turn the

alarm (buzzer) OFF when inspecting for cause.

WARNING! Inspect and repair the abnormality

immediately.

Backlight Switch

Turns instrument panel backlighting OFF or ON.

Hourmeter

Shows the total number of operating hours. Can be used as a

guide for periodic maintenance checks. The hourmeter is

located at the bottom of the tachometer.

Engine (Lube) Oil Pressure Gauge

Shows the engine (lube) oil pressure.

Fresh Water (Coolant) Temperature Gauge

Shows the cooling fresh water temperature.

Turbocharger Boost Pressure Gauge

Shows the intake air pressure (intake air boost pressure of

turbocharger).

Preheat Indicator (If equipped)

Illuminates when the air heater is heating up for easier starting

in cold temperatures. Indicator is located in the warning lamp

cluster.

*

The engine cannot be stopped by the starter (key) switch. Use the engine stop button to turn engine OFF.

**

Releasing the engine stop button before the engine has stopped rotating will cause the engine to continue to
run.

PRODUCT OVERVIEW

6LPA Series Operation Manual

19

© 2007 Yanmar Marine International

Summary of Contents for 6LPA-STP2















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands