manualshive.com logo in svg

Yanmar 3YM30, Installation Manual

Share
Download
Yanmar 3YM30 Installation Manual Download Page 22

3YM30

SPECIFICATIONS

3YM30-22

Marine Installation Manual - Volume 2

Cold Starting Aids

The 3YM30 engine is not equipped with cold 
starting aids.

Air Venting

The 3YM30 uses either a KM2P-1 marine gear or a 
SD20 sail drive, no venting device is needed.

Water Heater Tank Connection

The 3YM30 engine supports water heating tank 
connections for onboard head and galley operation.

Figure - 19

Optional Accessories

The following is a list of the 3YM30 optional 
accessories.

• New B-type (VDO) panel

• New extension wire harness (EWN3)

• Battery switch (BS500)

• Side-mount single control head (MORSE: MV)

• Top-mount single control head (MORSE: MT3)

• Push-pull control cable (MORSE: 33C) (RC4, 

RC7)

• Propeller shaft half coupling, slit (CSG1)

• Propeller shaft half coupling, taper (CTG1, 

CTG2, CTG3, CTG4)

• Propeller shaft half coupling, straight (CRG1)

• Lube oil evacuation pump (EPP1)

• Electric-type bilge pump, 12 V (BP1)

• Seacock (K1, K2)

• Fuel tank 30 L (8 gal) (FT1)

• Alternator, 12 V - 80A

• U-type, water mixing elbow

00027

8

1

(1)

(2)

1. Water to Tank
2. Water from Tank

JUN 2006 (Rev. 1)

Summary of Contents for 3YM30























Reviews:

No comments

Brands by name

Popular brands

Load more brands