Yanmar 3YM30 Service Manual Download Page 103

Page: 103 / 231

4. Disassembly and reassembly

(15)Removing the fuel injection nozzles

Loosen the fuel nozzles and remove them from the
cylinder head.

(16)Remove the fuel injection pump

1) Loosen the drive gear nut for fuel pump drive gear, and pull out the fuel pump drive gear /flange

assembly with an extraction tool.

Note:

Don't disassemble the pump flange and the pump drive gear.

2) Loosen the three (3) nuts for the fuel pump and remove the fuel injection pump and O-ring from the

gear case.

Fuel injection nozzle

Nozzle protector

Nozzle seat

Cylinder head

Gear case cover

Fuel injection pump

Pump flange

Fuel pump drive gear

Don’t disassemble!

Drive gear nut

Pump flange bolt

Summary of Contents for 3YM30








































































































































































































































Search results

Summary of Contents for 3YM30

Reviews:

Related manuals for 3YM30

Brands by name

Popular brands

Yanmar 3YM30, Service Manual

Search results

Summary of Contents for 3YM30

Reviews:

Related manuals for 3YM30

Brands by name

Popular brands