manualshive.com logo in svg

Yamato DP-5602, Operation Manual

Share
Download
Yamato DP-5602 Operation Manual Download Page 9

 

5

 

 

How to install the wall mount bracket

Installation procedure 

1. 

First, remove the 4 set screws 

 on the back of 

the indicator. Then install the supplied 2 wall 
mount brackets 

 by firmly tightening the 4 

screws 

 (make sure to insert the 4 washers 

 

between the indicator and the 2 wall mount 
brackets 

). 

2. 

Install the 2 wooden tapping screws 

 to a wall 

or post, as shown in the following figure. 

105 mm (installation pitch) 

3. 

Using the upper holes of the 2 wall mount 
brackets 

 set in the above step 1, hook the 

brackets onto the 2 wooden tapping screws 

 

set in the above step 2. The installation is now 
complete. 

<Caution> 

Since the 4 set screws 

 have been tightened to a 

fixed torque at the factory, the enclosure is 
water-proof and dust-proof (i.e. IP66 protection 
rating), easy to wash, and hygienically sound 
(HACCP compliance). However, for the wall-mount 
type indicators, the user must remove the set screws 

 and then install the wall mount brackets 

. 

Therefore, the “IP66” and “HACCP compliance” 
cannot be assured if the set screws 

 are not firmly 

tightened or if the wall mount brackets 

 are 

externally installed.

 

Wall or post

 

Summary of Contents for DP-5602















































Reviews:

No comments

Brands by name

Popular brands

Load more brands