YAMARIN Cross 53 Bow Rider Owner'S Manual Download Page 37

Page: 37 / 40

Yamarin Cross 53 Bow Rider

37 (40)

1. Fuel tank

5. Fuel tank filling hose

2. Fuel tank sensor

6. Fuel filling

3. Fuel feeding hose

7. Fuel tank vent

4. Fuel filter

8. Fuel tank breather hose

The fuel tank's filling vent is located on swim platform on right-hand (viewed from the
stern).

8.3

Steering system

The Yamarin Cross 53 BR is equipped with cable steering. The length of the steering cable is
3.9

metres ( 13 feet).

NOTE!

If you want to replace a component in the steering system, please
note that all components must conform to the ISO 10592
standard and carry the CE mark.

8.4

Electrical system

The

Yamarin Cross 53 BR's electrical system contains the following main components:

WIRE HARNESS

MAIN SWITCH AND FUSE PANEL

2 PCS 12 V POWER OUTLETS

NAVIGATION LIGHTS

In addition, the engine is an essential part of the boat's electrical system, which functions

Summary of Contents for Cross 53 Bow Rider









































Search results

Summary of Contents for Cross 53 Bow Rider

Reviews:

Related manuals for Cross 53 Bow Rider

Brands by name

Popular brands

YAMARIN Cross 53 Bow Rider, Owner'S Manual

Search results

Summary of Contents for Cross 53 Bow Rider

Reviews:

Related manuals for Cross 53 Bow Rider

Brands by name

Popular brands