background image

 

Trouble Recovery

 

67

 

Q. Is heat range of spark plug incorrect?
A. Inspect spark plug and replace it with rec-
ommended type.

Q. Is high pressure fuel pump drive belt bro-
ken?
A. Have serviced by a Yamaha dealer.

Q. Is engine not responding properly to shift
lever position?
A. Have serviced by a Yamaha dealer.

 

Engine vibrates excessively.

 

Q. Is propeller damaged?
A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged?
A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled
on propeller?
A. Remove and clean propeller.

Q. Is motor mounting bolt loose?
A. Tighten bolt.

Q. Is steering pivot loose or damaged?
A. Tighten or have serviced by a Yamaha
dealer.

 

EMU29430

 

Temporary action in 

emergency

 

EMU29440

 

Impact damage

WARNING

 

EWM00870 

 

The outboard motor can be seriously
damaged by a collision while operating or
trailering. Damage could make the out-

 

board motor unsafe to operate.

 

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

1.

Stop the engine immediately.

2.

Inspect the control system and all com-
ponents for damage. Also inspect the
boat for damage.

3.

Whether damage is found or not, return
to the nearest harbor slowly and careful-
ly.

4.

Have a Yamaha dealer inspect the out-
board motor before operating it again.

 

EMU29450

 

Running single engine

 

When using only engine in an emergency, be
sure to keep the unused one tilted up and op-
erate the other engine at low speed.

CAUTION:

 

ECM00370 

 

If the boat is operated with one engine in
the water but not running, water may run
into the exhaust pipe due to wave action,

 

causing engine trouble.

NOTE:

 

When you are maneuvering at low speed,
such as near a dock, it is recommended that
both engines be running with one in neutral

 

gear if possible.

Summary of Contents for Z300C





















































































Reviews: