Yamaha Z300C Owner'S Manual Download

Page: 48 / 84

Operation

EMU28051

Procedure for tilting down (power
trim and tilt/power tilt models)

Power trim and tilt model / power tilt model
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt
support lever / tilt support knob becomes
free.

Release the tilt support lever or pull out
the tilt support knob.

Push the power tilt / power trim and tilt
switch “

” (down) to lower the outboard

motor to the desired position.

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU28090

Power trim and tilt models / power tilt
models

The outboard motor can be tilted up partially
to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-

ZMU01885

ZMU01936

ZMU01980

ZMU01979

Summary of Contents for Z300C





















































































Search results

Summary of Contents for Z300C

Reviews:

Related manuals for Z300C

Brands by name

Popular brands

Yamaha Z300C, Owner'S Manual

Search results

Summary of Contents for Z300C

Reviews:

Related manuals for Z300C

Brands by name

Popular brands