Yamaha YZF-R1LEVC Supplementary Service Manual Download

Page: 77 / 87

ENG

NOTE:

When adjusting the clutch assembly width [by
replacing the clutch plate(s)], be sure to
replace the clutch plate

fast.

After replacing the clutch plate

, if specifica-

tions cannot be met, replace the clutch plate

EAS00282

CHECKING THE CLUTCH SPRINGS

(YZF-R1LE)
The following procedure applies to all of the
clutch springs.
1. Check:

• clutch spring

Damage

→

Replace the clutch springs as a

set.

2. Measure:

• clutch spring free length

Out of specification

→

Replace the clutch

springs as a set.

EAS00284

CHECKING THE CLUTCH HOUSING

(YZF-R1LE)
1. Check:

• clutch housing dogs

Damage/pitting/wear

→

Deburr the clutch

housing dogs or replace the clutch housing.

NOTE:

Pitting on the clutch housing dogs will cause
erratic clutch operation.

2. Check:

• bearing

Damage/wear

→

Replace the bearing and

clutch housing.

Clutch spring free length

43.8 mm (1.72 in)
<Limit>: 41.6 mm (1.64 in)

CLUTCH

Summary of Contents for YZF-R1LEVC
























































































Search results

Summary of Contents for YZF-R1LEVC

Reviews:

Related manuals for YZF-R1LEVC

Brands by name

Popular brands

Yamaha YZF-R1LEVC, Supplementary Service Manual

Search results

Summary of Contents for YZF-R1LEVC

Reviews:

Related manuals for YZF-R1LEVC

Brands by name

Popular brands