Yamaha YFM90RYXJ Owner'S Manual Download | Manualshive

Page: 97 / 132

background image

8-14

8

9. Check the engine oil filler cap O-ring for dam-

age, and then install and tighten the engine oil
filler cap.

10. Start the engine, and then let it idle for several

minutes while checking it for oil leakage. If oil
is leaking, immediately turn the engine off and
check for the cause.

11. Turn the engine off, wait at least ten minutes,

and then check the oil level and correct it if
necessary.

EBU34472

Transmission oil

The transmission case must be checked for oil
leakage before each ride. If any leakage is found,
have a Yamaha dealer check and repair the ATV.
In addition, the transmission oil must be changed
at the intervals specified in the periodic mainte-
nance and lubrication chart.

To change the transmission oil

1. Place the ATV on a level surface.
2. Place an oil pan under the transmission case

to collect the used oil.

3. Remove the transmission oil filler cap and its

O-ring from the transmission case.

4. Remove the transmission oil drain bolt and its

gasket to drain the oil from the transmission
case.

1. Transmission oil filler cap
2. O-ring

1

2

UBD362E0.book Page 14 Tuesday, January 31, 2017 5:10 PM

«
...
95
96
97
98
99
...
»

Summary of Contents for YFM90RYXJ





































































































































Reviews:

No comments

Related manuals for YFM90RYXJ

Brand: E-TON Pages: 30

Polar Trailer 10537

Brand: Clam Pages: 7

Brand: Moni Pages: 27

Brand: Can-Am Pages: 160

Brand: Erde Pages: 4

Sportsman 850 Touring EPS

Brand: Polaris Pages: 167

Brand: Eagle Pages: 12

OneStopGardens 91240

Brand: Harbor Freight Tools Pages: 7

Brand: Federal Signal Corporation Pages: 140

Brand: Yerf-Dog Pages: 21

Brand: GARIA Pages: 118

Pioneer 1000 2017

Brand: Honda Pages: 307

Brand: MANCO Pages: 16

Brand: Toro Pages: 2

CF MOTO CFORCE 625

Brand: DFK Pages: 64

MAR AMT TRAILER

Brand: Marlon Pages: 12

Brand: Grizzly Pages: 12

Brand: Grizzly Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands