Yamaha YFM450FAZ Owner'S Manual Download

Page: 157 / 166

10-3

Fuel:

Recommended fuel:

YFM450FAZ Unleaded gasoline only
YFM45FGHZ Regular unleaded gasoline only
YFM45FGZ Regular unleaded gasoline only

Fuel tank capacity:

15.0 L (3.96 US gal, 3.30 Imp.gal)

Fuel reserve amount:

4.5 L (1.19 US gal, 0.99 Imp.gal)

Carburetor:

Type

quantity:

BSR33 x 1

Spark plug (s):

Manufacturer/model:

NGK/DR8EA

Spark plug gap:

0.6–0.7 mm (0.024–0.028 in)

Clutch:

Clutch type:

Wet, centrifugal automatic

Transmission:

Primary reduction system:

V-belt

Secondary reduction system:

Shaft drive

Secondary reduction ratio:

39/24

24/18

33/9 (7.944)

Transmission type:

V-belt automatic

Operation:

Left hand operation

Reverse gear:

29/17 (1.706)

Low range:

45/16 (2.813)

High range:

38/23 (1.652)

Chassis:

Frame type:

Steel tube frame

Caster angle:

2.5 °

Trail:

8.5 mm (0.33 in)

Front tire:

Type:

Tubeless

Size:

AT25 x 8-12

Manufacturer/model:

YFM450FAZ CHENG SHIN/C-828
YFM45FGHZ MAXXIS/M979
YFM45FGZ MAXXIS/M979

Rear tire:

Type:

Tubeless

Size:

AT25 x 10-12

Manufacturer/model:

YFM450FAZ CHENG SHIN/C-828
YFM45FGHZ MAXXIS/M980
YFM45FGZ MAXXIS/M980

U37S61E0.book Page 3 Tuesday, June 2, 2009 10:33 AM

Summary of Contents for YFM450FAZ







































































































































































Search results

Summary of Contents for YFM450FAZ

Reviews:

Related manuals for YFM450FAZ

Brands by name

Popular brands

Yamaha YFM450FAZ, Owner'S Manual

Search results

Summary of Contents for YFM450FAZ

Reviews:

Related manuals for YFM450FAZ

Brands by name

Popular brands