Yamaha YFM450FAZ Owner'S Manual Download | Manualshive

Page: 126 / 166

background image

8-38

8

4. Tighten the locknut.
5. Slide the rubber cover to its original position.

EBU24060

Valve clearance

The valve clearance changes with use, resulting in
improper air-fuel mixture and/or engine noise. To
prevent this from occurring, the valve clearance
must be adjusted by a Yamaha dealer at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU24071

Adjusting the drive select lever safety
system cable

The drive select lever safety system cable stretch-
es with use, which can result in improper function.
Therefore, the safety system cable should be
checked and adjusted by a Yamaha dealer at the
intervals specified in the periodic maintenance and
lubrication chart.

EBU29601

Brakes

Replacement of brake components requires pro-
fessional knowledge. Brake service should be per-
formed by a Yamaha dealer.

WARNING

EWB02571

Operating with improperly serviced or adjust-
ed brakes could lead to a loss in braking ability
and an accident.

1. Rubber cover
2. Throttle cable free play adjusting bolt

3. Locknut

4. Throttle cable free play

U37S61E0.book Page 38 Tuesday, June 2, 2009 10:33 AM

«
...
124
125
126
127
128
...
»

Summary of Contents for YFM450FAZ







































































































































































Reviews:

No comments

Related manuals for YFM450FAZ

Brand: Parkside Pages: 89

Brand: Parkside Pages: 28

Super Adventure 2016

Brand: KTM Pages: 25

Brand: BMW Pages: 16

Brand: KTM Pages: 36

Brand: DYNATEK Pages: 4

Brand: DYNATEK Pages: 5

Brand: DYNATEK Pages: 5

Brand: SCHUBERTH Pages: 43

Brand: Aim Pages: 5

Brand: KTM Pages: 20

Brand: Can-Am Pages: 195

Brand: Sealey Pages: 2

X-Small Dry Duffel Bag

Brand: Tusk Pages: 3

Brand: Yamaha Pages: 3

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 23

Brand: Yamaha Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands