Yamaha XT660R 2007 Supplementary Service Manual Download Page 61 | Manualshive

Page: 61 / 81

background image

– 55 –

FI

FUEL INJECTION SYSTEM

41

Open or short circuit is detected in the
lean angle cut-off switch.

• Open or short circuit in wire harness
• Defective lean angle cut-off switch
• Disconnected lean angle cut-off switch coupler
• Malfunction in ECU

08

42

No normal signals are received from
the speed sensor or an open or short
circuit is detected in the neutral
switch.

• Open or short circuit in wire harness
• Defective speed sensor
• Disconnected speed sensor coupler
• Malfunction in vehicle speed sensor detected unit
• Defective neutral switch
• Disconnected neutral switch connector
• Malfunction in the engine side of the neutral switch
• Malfunction in ECU

07
21

43

Power supply to the injector and fuel
pump is not normal. (The ECU is
unable to monitor the battery voltage.)

• Open circuit in wire harness
• Malfunction in ECU
• Defective fuel injection system relay

09, 50

44

An error is detected while reading or
writing on EEPROM.

• Malfunction in ECU (The CO adjustment value is not

properly written on or read from the internal memory.)

60

46

Power supply to the fuel injection sys-
tem relay is not normal.

• Open circuit in wire harness
• Malfunction in rectifier/regulator
• Malfunction in A.C. magneto rotor

Refer to “CHARGING SYSTEM” in chapter 8.
(Manual No.: 5VK1-AE1)

09

50

Faulty ECU memory. When this mal-
function is detected, the code number
might not appear on the meter.

• Malfunction in ECU (The program and data are not prop-

erly written on or read from the internal memory.)

—

Er-1

No signals are received from the
ECU.

• Open or short circuit in sub-wire harness
• Disconnected ECU coupler
• Malfunction in meter
• Malfunction in ECU

—

Er-2

No signals are received from the ECU
within the specified duration.

• Improper connection in sub-wire harness
• Disconnected ECU coupler
• Malfunction in meter
• Malfunction in ECU

—

Er-3

Data from the ECU cannot be
received correctly.

• Improper connection in sub-wire harness
• Disconnected ECU coupler
• Malfunction in meter
• Malfunction in ECU

—

Er-4

Non-registered data has been
received from the meter.

• Improper connection in sub-wire harness
• Disconnected ECU coupler
• Malfunction in meter
• Malfunction in ECU

—

Fault

code No.

Symptom

Probable cause of malfunction

Diagnostic code

«
...
59
60
61
62
63
...
»

Summary of Contents for XT660R 2007


















































































Reviews:

No comments

Related manuals for XT660R 2007

Brand: Kappa Pages: 4

Brand: GIVI Pages: 3

Brand: Termignoni Pages: 9

Quantum hardcoated N30214-WK

Brand: National Cycle Pages: 13

Spyder RT Series

Brand: Can-Am Pages: 52

Brand: Two Brothers Racing Pages: 2

Brand: Memphis Shades Pages: 2

Brand: DYNATEK Pages: 5

Brand: MZ Pages: 82

Brand: BMS Pages: 12

Brand: APRILIA Pages: 235

Brand: hepco & becker Pages: 5

Brand: hepco & becker Pages: 6

Brand: Cocoon Pages: 16

Brand: DAELIM Pages: 62

Speedglas 9100 MP

Brand: 3M Pages: 108

Brand: Kabuto Pages: 32

Brand: Baja Designs Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands