Yamaha XT660R 2007 Supplementary Service Manual Download Page 33

Page: 33 / 81

– 27 –

CHK

ADJ

ADJUSTING THE DRIVE CHAIN SLACK

4. Adjust:

• drive chain slack

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

a. Loosen the wheel axle nut

b. Loosen both locknuts

c. Turn both adjusting nuts

or both adjust-

ing bolt

in direction

until the

specified drive chain slack is obtained.

NOTE:

To maintain the proper wheel alignment, adjust
both sides evenly.

d. Tighten both locknuts to the specified

torque.

e. Tighten the wheel axle nut to the specified

torque.

▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲ ▲▲▲

▲

▲▲▲

XT660R

XT660X

Direction

Drive chain is tightened.

Direction

Drive chain is loosened.

Locknut

16 Nm (1.6 m · kg, 11 ft · lb)

Wheel axle nut
105 Nm (10.5 m · kg, 75 ft · lb)

Summary of Contents for XT660R 2007


















































































Search results

Summary of Contents for XT660R 2007

Reviews:

Related manuals for XT660R 2007

Brands by name

Popular brands

Yamaha XT660R 2007, Supplementary Service Manual

Search results

Summary of Contents for XT660R 2007

Reviews:

Related manuals for XT660R 2007

Brands by name

Popular brands