Yamaha XR1800Z Ower'S Manual Download Page 84 | Manualshive

Page: 84 / 110

background image

4-13

STEERING CABLE INSPECTION

Be sure to check:

1) Check for smooth operation of the

wheel and steering nozzles.

2) Check for proper steering adjust-

ment. The nozzles should both point
straight back when the steering
wheel is centered.

If steering is stiff or misadjusted, ask
your Yamaha dealer to service it.

THROTTLE CABLE INSPECTION

Push and pull the throttle levers
through their full range with the shift
lever in Neutral. Repeat with the shift
lever in Forward, and again in Reverse.
Both throttle levers should move
smoothly from idle to full throttle and
back. If not, ask your Yamaha Sport
Boat dealer for service.

Improper throttle operation could
result in an accident. Check for
proper throttle operation before
starting the engines.

CHOKE CABLE ADJUSTMENT

Pull the choke knob out until it stops.
Release the knob. The knob should not
move. If it moves back on its own, tight-
en the friction adjustment slightly. If the
knob is difficult to move, loosen the fric-
tion adjustment slightly.

M

AINTENANCE

& C

ARE

4

WARNING

«
...
82
83
84
85
86
...
»

Summary of Contents for XR1800Z















































































































Reviews:

No comments

Related manuals for XR1800Z

Brand: Hobie Pages: 2

Brand: Westport Pages: 11

Brand: Cobalt Digital Inc Pages: 128

Brand: Cobalt Digital Inc Pages: 124

Brand: Grady-White Boats Pages: 128

Brand: Rondar Pages: 16

2010 Ranger Tug R-29

Brand: Rangertugs Pages: 21

SUN ODYSSEY 42 DS

Brand: Jeanneau Pages: 30

sun odyssey 54 DS

Brand: Jeanneau Pages: 115

Grand Soleil 50

Brand: Cantiere Del Pardo Pages: 124

SUPERJET 700 2003

Brand: Yamaha Pages: 109

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 134

Brand: NorthStar Pages: 2

Brand: Hobie Pages: 16

Sun Marine Frp-330

Brand: boAt Pages: 3

Brand: intrepid Pages: 85

Brand: Windworks Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands