CHASSIS
3-25
vehicle is used in dusty areas.
This vehicle has a drive chain with small rubber
O-rings between each side plate. Steam clean-
ing, high-pressure washing, certain solvents,
and the use of a coarse brush can damage
these O-rings. Therefore, use only kerosene to
clean the drive chain. Wipe the drive chain dry
and thoroughly lubricate it with engine oil or
chain lubricant that is suitable for O-ring chains.
Do not use any other lubricants on the drive
chain since they may contain solvents that could
damage the O-rings.
EAS21510
CHECKING AND ADJUSTING THE
STEERING HEAD
1. Stand the vehicle on a level surface.
WARNING
EWA13120
Securely support the vehicle so that there is
no danger of it falling over.
NOTE:
Place the vehicle on a suitable stand so that the
front wheel is elevated.
2. Check:
●
Steering head
Grasp the bottom of the front fork legs and
gently rock the front fork.
Blinding/looseness
→
Adjust the steering
head.
3. Remove:
●
Handlebar
Refer to “HANDLEBAR” on page 4-34.
●
Upper bracket
Refer to “STEERING HEAD” on page 4-49.
4. Adjust:
●
Steering head
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
a. Remove the lock washer “1”, the upper ring
nut “2”, and the rubber washer “3”.
b. Tighten the lower ring nut “4” with a steering
nut wrench “5”.
c. Turn the front fork to the right and left a few
times, and make sure that the steering ro-
tates smoothly. If it does not turn smoothly,
remove the lower bracket and inspect the up-
per and lower bearings.
Refer to “STEERING HEAD” on page 4-49.
d. Loosen the lower ring nut “4” fully turn and
then tighten it to specification with a steering
nut wrench.
WARNING
EWA13140
Do not overtighten the lower ring nut.
e. Install the rubber washer.
f. Install the upper ring nut.
g. Finger tighten the upper ring nut “2”, then
align the slots of both ring nuts. If necessary,
Recommended lubricant
Engine oil or chain lubricant
suitable for O-ring chains
Steering nut wrench
90890-01403
Spanner wrench
YU-33975
Lower ring nut (initial tightening
torque)
38 Nm (3.8 m•kg, 27 ft•lb)
Lower ring nut (final tightening
torque)
7 Nm (0.7 m•kg, 5.1 ft•lb)
5
4
T
R
.
.
T
R
.
.
Summary of Contents for WR250R
