manualshive.com logo in svg

Yamaha WaveRunner VX Sport 2014, Owner'S/Operator'S Manual, Page: 77 / 98

Share
Download
Yamaha WaveRunner VX Sport 2014 Owner'S/Operator'S Manual Download Page 77

Operation

71

speed. If weeds may have clogged the intake
area, clean the jet intake. (See page 85 for in-
formation on the jet intake.)

EJU40242

After removing the watercraft from 
the water

NOTICE

ECJ01311

Do not run the engine over 4000 r/min on
land. Also, do not run the engine for more
than 15 seconds without supplying water,
otherwise the engine could overheat.

After operating and removing the watercraft
from the water, promptly discharge the re-
maining water from the cooling water pas-
sages.
To discharge water from the cooling water
passages:
(1) Make sure that the area around the wa-

tercraft is clear, and then start the en-
gine.

(2) Discharge the remaining water out of the

cooling water passages by alternately
squeezing and releasing the throttle lever
quickly for 10 to 15 seconds.

(3) Stop the engine.

UF2P71E0.book  Page 71  Wednesday, July 10, 2013  5:37 PM

Summary of Contents for WaveRunner VX Sport 2014



































































































Reviews:

No comments