manualshive.com logo in svg

Yamaha WaveRunner VX Sport 2014, Owner'S/Operator'S Manual, Page: 52 / 98

Share
Download
Yamaha WaveRunner VX Sport 2014 Owner'S/Operator'S Manual Download Page 52

Operation and handling requirements

46

To check the engine oil level:
(1) With the engine stopped, place the wa-

tercraft in a precisely level position on
land or launch the watercraft.

(2) Look in all directions, and then start the

engine. (See page 60 for information on
starting the engine.)

(3) Run the engine at idling speed for 6 min-

utes or more. Run the engine an addi-
tional 5 minutes if the ambient
temperature is 20 °C (68 °F) or less.

(4) Stop the engine.
(5) Remove the seat. (See page 38 for seat

removal and installation procedures.)

(6) Loosen the oil tank filler cap and remove

it, and then wipe the attached dipstick
clean.

(7) Screw the oil tank filler cap into the filler

hole until it stops. Remove the oil tank
filler cap again and make sure that the

engine oil level is between the minimum
and maximum level marks.

(8) If the engine oil level is significantly

above the maximum level mark, consult
a Yamaha dealer. If the engine oil level is
below the minimum level mark, slowly
add engine oil.

(9) Repeat steps 6–8 until the engine oil is at

the proper level.

(10) Securely install the oil tank filler cap and

turn it until it stops.

(11) Securely install the seat in its original po-

sition.

1

Oil tank filler cap/Dipstick

1

1

Dipstick

2

Maximum level mark

3

Minimum level mark

2

1

3

UF2P71E0.book  Page 46  Wednesday, July 10, 2013  5:37 PM

Summary of Contents for WaveRunner VX Sport 2014



































































































Reviews:

No comments