manualshive.com logo in svg

Yamaha WaveRunner VX Sport 2014, Owner'S/Operator'S Manual, Page: 46 / 98

Share
Download
Yamaha WaveRunner VX Sport 2014 Owner'S/Operator'S Manual Download Page 46

Equipment operation

40

EJU34873

Bow eye

The bow eye is used to attach a rope to the
watercraft when transporting, mooring, or
towing it in an emergency. (See page 88 for
information on towing the watercraft.)

EJU34882

Stern eyes

The stern eyes are used to attach a rope to
the watercraft when transporting or mooring
it.

EJU40421

Cleat

The cleat is used to attach a ski rope to the
watercraft when pulling a water-skier.

WARNING! Do not use the cleat to lift the
watercraft. The cleat is not designed to
support the watercraft’s weight. If the

cleat breaks, the watercraft could fall,
which could result in severe injury.

 [EWJ01511]

EJU31684

Storage compartments

This watercraft is equipped with the following
storage compartments.
The storage compartments are not designed
to be waterproof. If you carry objects that
must  be  kept  dry,  put  them  in  a  waterproof
bag.
Make sure that the storage compartments
are closed securely before operating the wa-
tercraft.

EJU31716

Bow storage compartment

The bow storage compartment is located un-
der the hood.

1

Bow eye

1

Stern eye

1

1

1

Cleat

1

UF2P71E0.book  Page 40  Wednesday, July 10, 2013  5:37 PM

Summary of Contents for WaveRunner VX Sport 2014



































































































Reviews:

No comments