background image

E

2-12

EMU01687

Hour Meter

This meter shows the number of hours the
engine has been run. It can be set to show
the total nu0mber of hours or the number of
hours for the current trip. The display can
also be turned on and off.

8

Changing the display format
Pressing the MODE button changes the
display format in the following circular pat-
tern:
Total hours - Trip hours - Display off

8

Resetting the trip hours
Simultaneously pressing the SET and
MODE buttons for more than 1 second
while the trip hours are displayed resets
the trip counter to 0 (zero).

NOTE:

The total number of hours the engine has
been run cannot be reset.

EMU00138

Oil-Level Indicator

This indicator shows the engine oil level. If
the oil level falls below the lower limit, the
warning indicator will start to blink. Refer to
the sections “FILLING OIL” and “OIL LEVEL
WARNING” for details.

1

Oil-level indicator

c

C

Do not operate the engine without oil.
Serious engine damage will occur.

001087

001051

q

 60V-9-13-2  7/28/03 5:36 PM  Page 13

Summary of Contents for VZ225C





























































































































Reviews: