manualshive.com logo in svg

Yamaha VX WaveRunner 2007, Owner'S/Operator'S Manual, Page: 94 / 108

Share
Download
Yamaha VX WaveRunner 2007 Owner'S/Operator'S Manual Download Page 94

Trouble recovery

89

EJU34560

Troubleshooting 

If you have any trouble with your watercraft, use this section to check for the possible cause.
If you cannot find the cause, or if the procedure for replacement or repair is not described in
this owner’s/operator’s manual, have a Yamaha dealer perform the necessary service.

EJU34611

Troubleshooting chart 

TROUBLE

POSSIBLE CAUSE

REMEDY

PAGE

Engine does not 
start (Starter motor 
does not turn over)

Engine shut-
off switch

Clip not in place

Install clip

31

Fuse

Burned out

Replace the fuse and 
check wiring

93

Battery

Run down

Recharge

85

Poor terminal con-
nections

Tighten as required

85

Terminal corroded

Clean

75

Starter motor

Faulty

Have serviced by 
Yamaha dealer

—

Engine does not 
start (Starter motor 
turns over)

Throttle lever

Squeezed

Release

32

Fuel

Empty

Refill as soon as pos-
sible

48

Stale or contaminat-
ed

Have serviced by 
Yamaha dealer

80

Fuel tank

Water or dirt present

Have serviced by 
Yamaha dealer

80

Spark plug

Fouled or defective

Clean or replace

83

Spark plug 
cap

Not connected or 
loose

Connect properly

83

Connected to wrong 
cylinder

Connect properly

83

Fuel injec-
tion system

Fuel pump faulty

Have serviced by 
Yamaha dealer

—

UF1Y11E0.book  Page 89  Wednesday, August 23, 2006  11:43 AM

Summary of Contents for VX WaveRunner 2007













































































































Reviews:

No comments