Yamaha VX WaveRunner 2007 Owner'S/Operator'S Manual Download Page 60 | Manualshive

Page: 60 / 108

Yamaha VX WaveRunner 2007 Owner'S/Operator'S Manual Download Page 60

Operation

55

contact a Yamaha dealer or a fire extin-
guisher dealer to obtain one meeting the
proper specifications.

EJU32590

Throttle lever

Check the throttle lever for proper operation.
Squeeze and release the throttle lever several
times to make sure that there is no hesitation
in its travel. It should be smooth over the com-
plete range and spring back to the idle posi-
tion when released.

WARNING

EWJ00490

Before starting the engine, always check
the operation of the throttle lever.

EJU32610

Steering system

Check the handlebars for looseness.
Turn the handlebars as far as possible to the
right and left to make sure that operation is
smooth and unrestricted throughout the
whole range. Also, make sure that the jet
thrust nozzle moves as the handlebars are

turned, and that there is no free play between
the handlebars and the jet thrust nozzle.

Check that the handlebars are locked in
place. (See “Tilt lever” on page 33 for more in-
formation.)

EJU32630

Shift lever and reverse gate

Check the shift lever and reverse gate for
proper operation.
Make sure that the reverse gate goes down
completely when the shift lever is pulled up.

Fire extinguisher:

Classification:

B-1

Capacity:

2 lb or more

UF1Y11E0.book Page 55 Wednesday, August 23, 2006 11:43 AM

«
...
58
59
60
61
62
...
»

Summary of Contents for VX WaveRunner 2007













































































































Reviews:

No comments