manualshive.com logo in svg

Yamaha VX WaveRunner 2007, Owner'S/Operator'S Manual, Page: 42 / 108

Share
Download
Yamaha VX WaveRunner 2007 Owner'S/Operator'S Manual Download Page 42

Features and functions

37

EJU34880

Stern eyes 

The stern eyes are located at the stern of the
watercraft.
The stern eyes are used to attach a rope to
the watercraft when transporting or mooring it.

EJU31370

Yamaha Engine Management System 
(YEMS) 

This model is equipped with an integrated,
computerized management system that con-
trols and adjusts ignition timing, fuel injection,
engine diagnostics, and the off-throttle steer-
ing (OTS) system.

EJU34911

Multifunction information center 

The multifunction information center is
equipped with the following two main compo-

nents for help and convenience in operating
the watercraft.

CAUTION:

ECJ00071

Do not run the engine for more than 15
seconds without supplying water or over
4000 r/min on land when checking the op-
eration of the meter, otherwise the engine
could overheat.

NOTE:

●

When the multifunction information center
starts operating, the analog speedome-
ter/tachometer makes one sweep, all dis-
plays light up for 2 seconds, and then the
meter starts to operate normally.

●

The multifunction information center will
continue to operate for 25 seconds after the
engine stops.

1

Stern eye

1

Analog speedometer/tachometer and indi-
cator lights

2

Multifunction display and operation buttons

UF1Y11E0.book  Page 37  Wednesday, August 30, 2006  2:44 PM

Summary of Contents for VX WaveRunner 2007













































































































Reviews:

No comments