manualshive.com logo in svg

Yamaha V-Star 1300, Owner'S Manual

Share
Download
Yamaha V-Star 1300 Owner'S Manual Download Page 72

PERIODIC MAINTENANCE AND ADJUSTMENT

7-31

7

1. Remove the turn signal/position

light bracket cover by removing the
bolts.

2. Remove the headlight unit by re-

moving the bolts on each side.

3. Disconnect the headlight coupler,

and then remove the bulb cover.

4. Unhook the headlight bulb holder,

and then remove the burnt-out
bulb.

5. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

6. Install the headlight bulb cover,

and then connect the coupler.

7. Install the headlight unit by install-

ing the bolts.

8. Place the turn signal/position light

bracket cover in the original posi-
tion, and then install the bolts.

9. Have a Yamaha dealer adjust the

headlight beam if necessary.

1. Turn signal/position light bracket cover
2. Bolt

1. Bolt

1. Headlight bulb cover
2. Headlight coupler

1. Headlight bulb holder
2. Headlight bulb

U5S612E0.book  Page 31  Wednesday, April 9, 2008  5:56 PM

Summary of Contents for V-Star 1300





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands