manualshive.com logo in svg

Yamaha V-Star 1300, Owner'S Manual

Share
Download
Yamaha V-Star 1300 Owner'S Manual Download Page 57

PERIODIC MAINTENANCE AND ADJUSTMENT

7-16

7

3. Insert a new air filter element into

the air filter case. 

NOTICE:

 Make

sure that the air filter element is
properly seated in the air filter
case. The engine should never
be operated without the air filter
element installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.

[ECA10481]

4. Install the air filter case cover by in-

stalling the bolts.

EAU21382

Checking the throttle cable 
free play 

The throttle cable free play should mea-
sure 4.0–6.0 mm (0.16–0.24 in) at the
throttle grip. Periodically check the
throttle cable free play and, if neces-
sary, have a Yamaha dealer adjust it.

EAU21401

Valve clearance 

The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.

1. Air filter element

1. Throttle cable free play

U5S612E0.book  Page 16  Wednesday, April 9, 2008  5:56 PM

Summary of Contents for V-Star 1300





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands