manualshive.com logo in svg

Yamaha V-Star 1300, Owner'S Manual

Share
Download
Yamaha V-Star 1300 Owner'S Manual Download Page 37

FOR YOUR SAFETY – PRE-OPERATION CHECKS

5-3

5

Throttle grip

• Make sure that operation is smooth.
• Check cable free play.
• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and 

grip housing.

7-16, 7-24

Control cables

• Make sure that operation is smooth.
• Lubricate if necessary.

7-23

Wheels and tires

• Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary.

7-17, 7-18

Brake and shift pedals

• Make sure that operation is smooth.
• Lubricate pedal pivoting points if necessary.

7-24

Brake and clutch levers

• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.

7-25

Sidestand

• Make sure that operation is smooth.
• Lubricate pivot if necessary.

7-25

Chassis fasteners

• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.

—

Instruments, lights, signals 
and switches

• Check operation.
• Correct if necessary.

—

Sidestand switch 

• Check operation of ignition circuit cut-off system.
• If system is not working correctly, have Yamaha dealer check vehicle.

4-15

ITEM

CHECKS

PAGE

U5S612E0.book  Page 3  Wednesday, April 9, 2008  5:56 PM

Summary of Contents for V-Star 1300





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands