background image

Connection methods

- 13 -

 Owner’s Manual

Tio1608-D

English

Connection methods

This section explains the different methods for connecting 
the Tio1608-D to other Dante devices.

Quick Config (automatic setup) 

When connecting the unit to a TF series mixing console, 
Quick Config makes it easy to set up the unit automatically. 
It allows you to connect up to three Tio1608-D units to one 
TF series mixing console, and configures Dante network 
settings and audio signal settings in one operation.

Tio1608-D procedure

1.

With all the units turned off, set the DIP switches on 
the rear panel to the up position.

2.

Set the [QUICK CONFIG] switch on the front panel 
to the [ON] position.

3.

Set the [UNIT ID] switch on the front panel to the 
desired position.
If you are using multiple Tio1608-D units, make sure 
each unit has a unique UNIT ID setting.

4.

Use Ethernet cables to connect the Tio1608-D to the 
NY64-D card (installed in the TF series mixing 
console) or to other Tio1608-D units in a daisy-
chain configuration, as shown below.

When using Quick Config, the units will operate the same 
whether you connect the Ethernet cables to the [PRIMARY] or 
[SECONDARY] Dante connector.

When connecting 3 units

5.

Turn each device on.

TF series mixing console procedure

6.

Display the console's SYSTEM SETUP 

 SLOT SETUP 

screen, and confirm that Quick Config is enabled.

Now the TF series mixing console can recognize the 
Tio1608-D units, and all Dante settings and input and output 
patching settings will be configured automatically.

When the Quick Config button is displayed in white, Quick 
Config is enabled. If the button is grayed out, click it. If you 
cannot enable Quick Config, return to step 

1

 and confirm that 

the Tio1608-D is configured properly.

NOTE

An NY64-D audio interface card (sold separately) is required to 
connect a Tio1608-D to a TF series mixing console.

TF Series (NY64-D)

Tio1608-D UNIT ID=1

Tio1608-D UNIT ID=2

Tio1608-D UNIT ID=3

[PRIMARY] or 
[SECONDARY] 
connector

[PRIMARY] 
connector

[PRIMARY] 
connector

[SECONDARY] 
connector

[PRIMARY] or 
[SECONDARY] 
connector

[SECONDARY] 
connector

Summary of Contents for Tio1608-D

























Reviews: