Yamaha SXV70ERH Owner'S Manual Download

Page: 73 / 98

8-19

ESU00191

Ski spring preload adjustment

The spring preload can be adjusted by turning the spring
preload adjuster

For SXV70/SXV70ER

CD-11E

For SXV70M

CD-11E

CAUTION:

The left and right ski spring preload must be set to
the same pressure. Uneven settings can cause poor
handling and loss of stability.

WARNING

This shock absorber contains highly pressurized
nitrogen gas. It could explode by improper handling,
causing injury, or property damage.

●

Do not tamper with or attempt to open the shock
absorber.

●

Do not subject the shock absorber to an open
flame or other high heat source, which could
cause it to explode.

●

Do not deform or damage the shock absorber in
any way.

●

Do not dispose of a worn or damaged shock
absorber by yourself. Take the unit to a Yamaha
dealer.

Spring seat length

Standard

Long

←

→

Short

Preload

Hard

←

→

Soft

Length

Maximum
138.5 mm
(5.45 in)

128.5 mm

(5.06 in)

Minimum
118.5 mm
(4.76 in)

Spring seat length

Standard

Long

←

→

Short

Preload

Hard

←

→

Soft

Length

Maximum
125.5 mm
(4.94in)

115.5 mm

(4.55 in)

Minimum
105.5 mm
(4.15 in)

U8EK11.book Page 19 Thursday, April 25, 2002 5:10 PM

Summary of Contents for SXV70ERH



































































































Search results

Summary of Contents for SXV70ERH

Reviews:

Related manuals for SXV70ERH

Brands by name

Popular brands

Yamaha SXV70ERH, Owner'S Manual

Search results

Summary of Contents for SXV70ERH

Reviews:

Related manuals for SXV70ERH

Brands by name

Popular brands