background image

 

- 13 - 

7. Maintenance and Test Modes 

 

■Maintenance mode (measurement mode) 

 

Maintenance mode is a program to adjust the key sensor and damper pedal sensor 
detection positions by measurement. 
Measurement by maintenance mode shall be required in the following cases; 

If the detection position is out of standard, when checked in the test mode. 

When replacing the key sensor rail, damper pedal sensor and DM sheet, etc.   

                                   

 

[Key sensor measurement] 

For key sensor measurement, there are “All-key measurement” to rewrite the 

measurement of all keys and “1-key measurement” to rewrite only a designated key. 

 

 
Key sensor measurement “All-key measurement” / “1-key measurement” procedure 

No.  Measurement item 

All-key measurement

   

1-key measurement

   

 

 
 

Start-up 

10F#+12G#+14A#+ power 
ON (release keys in 2 sec.) 

 

A tone will be sounded at 

regular 2 sec intervals. 
(Waiting mode) 
→    Wait for about 30sec. 

9F+11G+ power ON (release 

keys 2 sec.) 

 

Two successive tones 

will be sounded at regular 1 
sec intervals. (Key selection 
status) *1 

 

Start of rest value 

measurement 

Depress the damper pedal. 

 

Two successive tones 

will be sounded at regular 1 
sec intervals. 

Press 1 key to be measured. 

 

The tone will change to 

the tone of the key to be 
measured. *2 

Rest value 

measurement 

Confirm that key is in the rest 
position. 

Confirm that key is in the rest 
position. 

 

Rest value registration 

Depress the damper pedal. 

 

Three successive tones 

will be sounded at regular 1 
sec intervals. 

Depress the damper pedal. 

 

Three successive tones 

will be sounded at regular 1 
sec intervals. 

End value 

measurement 

Press 1 to 88 keys lightly one 
by one to the end position. 

Press 1 to 88 keys lightly one 
by one to the end position. 

 

End value registration 

Depress the damper pedal. 

 

A tone will be sounded at 

regular 2 sec intervals. 

Depress the damper pedal. 

 

A tone will be sounded at 

regular 2 sec intervals. 

 

Flash RAM writing 

Depress the soft pedal. 

 

The writing will be 

completed in about 10 sec, 
then 76C will sound 3 times. 

Depress the soft pedal. 

 

The writing will be 

completed in about 10 sec, 
then 76C will sound 3 times. 

 

Complete 

Power OFF 

Power OFF 

Note 1: If the tone is consonant (“do”, “mi”, “sol” and “do”), the writing has already been done in the table.   
If the tone is dissonant, the writing has not been done in the table. 
Note 2: One key measurement requires the same procedure as for the measurement of all keys. 
If more than one key is to be measured, repeat the steps 3 through 6 and then proceed to step 7). 

Summary of Contents for Silent Piano GB1KS



















Reviews: