manualshive.com logo in svg

Yamaha RX10RTW, Owner'S Manual, Page: 72 / 100

Share
Download
Yamaha RX10RTW Owner'S Manual Download Page 72

8-22

ESU01811 

Changing the brake fluid

Brake fluid replacement is necessary when the following
components are replaced during the periodic mainte-
nance or if they are damaged or leaking.

a. All oil seals of the master cylinder and caliper cylinder

b. The brake hose

WARNING

@ 

Make sure that the brake fluid and the above parts
are replaced by a Yamaha dealer. 

@ 

ESU00183 

Suspension

The suspension can be adjusted to suit rider preference.
A softer setting, for example, may provide greater rider
comfort, while a harder setting may allow more precise
handling and control over certain types of terrain or riding
conditions.

WARNING

@ 

Be sure to have a Yamaha dealer make this adjust-
ment. 

@

ESU05100 

Adjusting the front shock absorber air pressure

This snowmobile is equipped with FOX shock absorbers
as standard equipment. 
The air pressure of the shock absorbers can be adjusted
using the special pump 

1

 included with your snowmo-

bile.

NOTE:

@ 

The following procedure applies to both shock absorb-
ers. 

@

1. Place the snowmobile on a level surface and apply

the parking brake. 

2. Lift the front of the snowmobile onto a suitable stand

to raise the skis off the ground.

WARNING

@ 

Support the snowmobile securely on a suitable
stand before adjusting the shock absorbers. 

@

E_8gt.book  Page 22  Tuesday, March 28, 2006  5:37 PM

Summary of Contents for RX10RTW





































































































Reviews:

No comments