Yamaha RX10RTW Owner'S Manual Download Page 20 | Manualshive

Page: 20 / 100

background image

5-2

ESU00361

Engine overheating prevention system

This model is equipped with an engine overheating pre-
vention system to prevent overheating when the engine
is idling.
When the engine has been idling for at least 3 minutes
and the coolant temperature has risen above 100 °C
(212 °F), the engine automatically shuts off to prevent
overheating.

NOTE:

The engine can be started after it shuts off.

ESU04701

Throttle override system (T.O.R.S.)

If the throttle bodies or throttle cable malfunctions during
operation, the T.O.R.S. will operate when the throttle
lever is released.
The T.O.R.S. is designed to interrupt the fuel injection
and keep the engine speed between 2,800 and
3,000 r/min if the throttle valves fail to return to the idle
position when the throttle lever is released.

WARNING

@

●

If the T.O.R.S. is activated, make sure that the
cause of the malfunction has been corrected and
that the engine can be operated without a prob-
lem before restarting the engine.

●

Be sure to use the specified spark plug and spark
plug cap. Otherwise, the T.O.R.S. will not work
properly.

@

E_8gt.book Page 2 Tuesday, March 28, 2006 5:37 PM

«
...
18
19
20
21
22
...
»

Summary of Contents for RX10RTW





































































































Reviews:

No comments

Related manuals for RX10RTW

Brand: Panasonic Pages: 2

Brand: Honda Pages: 513

Brand: Polaris Pages: 690

Formula Mx 1988

Brand: BOMBARDIER Pages: 62

traxter max series

Brand: BOMBARDIER Pages: 174

outlander max 800

Brand: BOMBARDIER Pages: 160

Brand: BOMBARDIER Pages: 282

Brand: Turftime Pages: 24

Brand: SunL Pages: 16

Amazon P80 2019

Brand: Morgan Olson Pages: 81

honey joy TY283250

Brand: Costway Pages: 28

Brand: KTM Pages: 247

2015 39 Roadster NEV

Brand: ACG Pages: 77

2010 Ranger RZR 800 EFI

Brand: Polaris Pages: 352

Sportsman 700 HO 2004

Brand: Polaris Pages: 139

Brand: Landoll Pages: 88

Brand: Ace Sports Pages: 10

Outlander Series 500

Brand: Can-Am Pages: 504

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands