Yamaha RX10RTW Owner'S Manual Download Page 71

Page: 71 / 100

8-21

1. Loosen the locknut

and the adjusting bolt

2. Loosen the cable locknut

3. Turn the cable adjuster

in or out to adjust the cable

length.

4. Tighten the cable locknut.
5. Turn the adjusting bolt in or out to adjust the clear-

ance between the parking brake pads

and the

brake disc

6. Tighten the locknut.

ESU00180

Checking the brake fluid level

Place the snowmobile on a level surface. Check that the
brake fluid is above the lower level and replenish when
necessary.

Lower level

WARNING

Be careful that water does not enter the master cylin-
der when refilling. Water will significantly lower the
boiling point of the fluid and may result in vapor
lock.
If the brake fluid level goes down, consult a Yamaha
dealer.

CAUTION:

Brake fluid may deteriorate painted surfaces or plas-
tic parts. Never spill any fluid. If any is spilled, clean
it up immediately.

Cable length

: 43.5–46.5 mm (1.713–1.831 in)

Clearance

: 1.5–2.0 mm (0.059–0.079 in)

Specified brake fluid: DOT 4

E_8gt.book Page 21 Tuesday, March 28, 2006 5:37 PM

Summary of Contents for RX10RTW





































































































Search results

Summary of Contents for RX10RTW

Reviews:

Related manuals for RX10RTW

Brands by name

Popular brands

Yamaha RX10RTW, Owner'S Manual

Search results

Summary of Contents for RX10RTW

Reviews:

Related manuals for RX10RTW

Brands by name

Popular brands