17
PSR-S770/PSR-S970
12. Wheel, MOD Circuit Board
(Time required: About 4 minutes)
12-1. Remove the lower case assembly. (See procedure 2.)
12-2. Remove the two (2) screws marked [500B]. The MOD
circuit board can then be removed with the wheel.
(Fig. 9)
*
The wheel is not part of the MOD circuit board. When
replacing the MOD circuit board, remove the wheel
from the MOD circuit board, and install it on the new
circuit board.
13. PNL Circuit Board
(Time required: About 5 minutes)
13-1. Remove the lower case assembly. (See procedure 2.)
13-2. Remove the keyboard assembly. (See procedure 10.)
13-3. Remove the ten (10) screws marked [500C]. The PNL
circuit board can then be removed. (Fig. 9)
*
When installing the PNL circuit board, tighten the
screws
z
and
x
shown in Fig. 9 in numerical order
and then tighten the other screws.
14. PNC Circuit Board
(Time required: About 5 minutes)
14-1. Remove the lower case assembly. (See procedure 2.)
14-2. Remove the keyboard assembly. (See procedure 10.)
14-3. Remove the ten (10) screws marked [500D]. The PNC
circuit board can then be removed. (Fig. 9)
*
When installing the PNC circuit board, tighten the
screws
z
and
x
shown in Fig. 9 in numerical order
and then tighten the other screws.
15. PNR Circuit Board
(Time required: About 5 minutes)
15-1. Remove the lower case assembly. (See procedure 2.)
15-2. Remove the keyboard assembly. (See procedure 10.)
15-3. Remove the nine (9) screws marked [500E]. The PNR
circuit board can then be removed. (Fig. 9)
*
When installing the PNR circuit board, tighten the
screws
z
and
x
shown in Fig. 9 in numerical order
and then tighten the other screws.
16. KNOB Circuit Board
(Time required: About 4 minutes)
16-1. Remove the lower case assembly. (See procedure 2.)
16-2. Remove the LIVE CONTROL knobs. (Fig. 5)
16-3. Remove the five (5) screws marked [500F]. The
KNOB circuit board can then be removed. (Fig. 9)
Projection [A] x 8
Projection [A] x 8
PB
KNOB
MOD
• UPPER CASE ASSEMBLY
[500E] x 9
[500D] x 10
[500C] x 10
z
x
z
x
PNC
PNL
z
x
PNR
* The eight (8) projections of the
left speaker grille must be bent in
the counterclockwise direction.
[500A]
[500B]
[500F] x 5
30°–40°
Fig. 9
Summary of Contents for PSR-S770
