43
P-80
8. SYSTEM EXCLUSIVE MESSAGES (XG Standard)
(1) XG Native Parameter Change
Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->
[mmH] -> [
ll
H] -> [ddH] -> [F7H]
F0H
= Exclusive status
43H
= YAMAHA ID
1nH
= When received, n=0~F.
When transmitted, n=0.
4CH
= Model ID of XG
hhH
= Address High
mmH
= Address Mid
ll
H
= Address Low
ddH
= Data
|
F7H
= End of Exclusive
Data size must match parameter size (2 or 4 bytes).
When the XG System On message is received, the MIDI system
will be reset to its default settings.
The message requires approximately 50ms to execute, so suffi-
cient time should be allowed before the next message is sent.
(2) XG Native Bulk Data (reception only)
Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->
[bbH] -> [hhH] -> [mmH] -> [
ll
H] ->
[ddH] ->...-> [ccH] -> [F7H]
F0H
Exclusive status
43H
YAMAHA ID
0nH
When received, n=0~F.
When transmitted, n=0.
4CH
Model ID of XG
aaH
ByteCount
bbH
ByteCount
hhH
Address High
mmH
Address Mid
ll
H
Address Low
ddH
Data
|
|
|
|
ccH
Check sum
F7H
End of Exclusive
• For information about the related XG parameters, refer to Tables
1, 2 and 3 below.
• Receipt of the XG SYSTEM ON message causes reinitialization
of relevant parameters and Control Change values. Allow suffi-
cient time for processing to execute (about 50 msec) before
sending the P-80 another message.
• XG Native Parameter Change message may contain two or four
bytes of parameter data (depending on the parameter size).
• For information about the Address and Byte Count values, refer
to Table 1 below. Note that the table’s Total Size value gives the
size of a bulk block. Only the top address of the block (00H, 00H,
00H) is valid as a bulk data address.
9. SYSTEM EXCLUSIVE MESSAGES
(Clavinova MIDI Format)
Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [nnH] ->
[F7H]
F0H
= Exclusive status
43H
= Yamaha ID
73H
= Clavinova ID
xxH
= Product ID (P-80 ID: 66H or CLP common ID: 01H)
nnH
= Substatus
nn
Control
02H
Internal MIDI clock
03H
External MIDI clock
06H
Bulk Data (the bulk data follows 06H)
F7H
= End of Exclusive
* When nn=02H or 03H, Clavinova common ID (01H) is
recognized as well as 66H or 01H.
BULK DUMP FORMAT
F0H, 43H, 73H
66H
=P-80 ID
06H
=Bulk ID
05H
=Sequence data
0nH, 0nH, 0nH, 0nH, 0nH, 0nH, 0nH, 0nH =Data length
[BULK DATA]
=
[CHECK SUM (1byte)] = 0-sum (BULK DATA)
F7H
= End of Exclusive
10. SYSTEM EXCLUSIVE MESSAGES (Special Control)
Data format: [F0H] -> [43H] -> [73H] -> [66H] -> [11H] ->
[0nH] -> [ccH] -> [vvH] -> [F7H]
F0H
= Exclusive status
43H
= Yamaha ID
73H
= Clavinova ID
66H
= P-80 ID
11H
= Special control
0nH
= Control MIDI change (n=channel number)
cc
= Control number
vv
= Value
F7H
= End of Exclusive
Control
0n
ccH
vvH
Split Point
Always 00H
14H
14H : Split Key Number
Metronome
Always 00H
1BH
00H : off
01H : –
02H : 2/4
03H : 3/4
04H : 4/4
06H : 6/4
7FH : No accent
Damper Level
ch: 00H-0FH
3DH (Sets the Damper Level
for each channel)
00H-7FH
Channel Detune
ch: 00H-0FH
43H (Sets the Detune value for
each channel)
00H-7FH
Voice Reserve
ch: 00H-0FH
45H
00H : Reserve off
7FH : on*
* When Volume, Expression is received for Reserve On, they will
be effective from the next Key On. Reserve Off is normal.
11. SYSTEM EXCLUSIVE MESSAGES (Others)
Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] ->
[00H] -> [00H] -> [mmH] -> [
ll
H] -> [ccH] ->
[F7H]
Master Tuning (XG and last message priority) simultaneously
changes the pitch of all channels.
F0H
= Exclusive Status
43H
= Yamaha ID
1nH
= When received, n=0~F.
When transmitted, n=0.
27H
= Model ID of TG100
30H
= Sub ID
00H
=
00H
=
mmH
= Master Tune MSB
ll
H
= Master Tune LSB
ccH
= don’t care (under 7FH)
F7H
= End of Exclusive
• This data will not be reset by GM SYSTEM ON or XG SYSTEM
ON message.
149
