Yamaha MW10c, Owner'S Manual

Page: 24 / 37

MW8CX/MW10C Owner’s Manual
Reference
90
Specifications
■
Electrical Specifications
■
General Specifications
All level controls are nominal if not specified.
Output impedance of signal generator: 150 ohms
* The MW8CX feature is described first, followed by the MW10C feature in brackets: MW8CX (MW10C)
MIN TYP MAX UNIT
Frequency Response STEREO OUT GAIN: min (CHs 1–5/6)
20 Hz–20 kHz
Nominal output level @1 kHz
-3.0 1.0
dB
EFFECT SEND
(AUX SEND*)
-3.0 1.0
MONITOR OUT, REC OUT -3.0 1.0
Total Harmonic Distor-
tion (THD + N) STEREO OUT +14 dBu, 20 Hz–20 kHz, Input Gain Control at minimum
0.1 %
Hum & Noise
Hum & Noise are mea-
sured with a 6 dB/
octave filter @12.7
kHz; equivalent to a 20
kHz filter with infinite
dB/octave attenuation.
Input: CH INPUT 1, 2 MIC EIN (Equivalent Input Noise): Rs = 150
Ω
, GAIN: maximum
(CH1, 2)
-128
dBu
STEREO OUT STEREO Master control at nominal level and all CH Level con-
trol at minimum.
-87
EFFECT SEND
(AUX SEND*)
All CH EFFECT (AUX*) controls at minimum.
-85
STEREO OUT STEREO Master control and one CH level control at nominal
level (CH1, 2)
-64
STEREO OUT Residual Output Noise -100
Crosstalk (1 kHz) Adjacent Input CH1, 2 -70
dB
Input to Output STEREO L/R, CH 1, 2, PAN: panned hard left or right -70
Maximum Voltage Gain
(1 kHz)
All level controls are
maximum when mea-
sured
PAN/BAL: panned
hard left or hard right.
Rs = 150
Ω
INPUT GAIN: maximum
MIC to CH INSERT OUT 60
dB
MIC to STEREO OUT 76
MIC to REC OUT 58.2
MIC to MONITOR OUT 92
MIC to PHONES OUT 81
MIC to EFFECT SEND (AUX SEND*) 76
LINE to STEREO OUT 50
LINE to EFFECT SEND (AUX SEND*) 47
ST CH 7/8, (CHs 7/8, 9/10*) to STEREO OUT 26
Rs = 150
Ω
RETURN to STEREO OUT 12
Rs = 600
Ω
2TR IN to STEREO OUT 23.8
Phantom Voltage MIC no load 48 V
USB Audio Input/Output: 44.1/48 kHz
Input HPF CHs 1–5/6, 80 Hz, 12 dB/oct
Input Equalization
Turn over/roll-off frequency
of shelving: 3 dB below
maximum variable level.
±15 dB maximum
CHs 1–5/6 HIGH: 10 kHz (shelving)
MID: 2.5 kHz (peaking)
LOW: 100 Hz (shelving)
CH 7/8 (CHs 7/8, 9/10*) HIGH: 10 kHz (shelving)
LOW: 100 Hz (shelving)
PEAK Indicator Red LED turns on when post EQ signal (either post MIC HA or post EQ signal for
CHs 3/4, 5/6) reaches -3 dB below clipping (+17 dBu).
Internal Digital Effect
(Only MW8CX) 16 PROGRAM, PARAMETER control
Foot Switch (Digital Effect On/Off)
LED Level Meter Pre MONITOR Level 2x7 points LED meter (PEAK, +6, +3, 0, -5, -10, -20 dB)
PEAK lights if the signal level reaches 3 dB below the clipping level.
Power Supply Adaptor PA-10 AC 38 VCT, 0.62 A, Cable Length = 3.6 m
Power Consumption 21 W
Dimensions (W x H x D) 256.6 mm x 62.2 mm x 302.5 mm
Net Weight 1.7 kg (MW8CX), 1.6 kg (MW10C)