Yamaha midnight star XVS1300A Owner'S Manual Download Page 73

Page: 73 / 90

PERIODIC MAINTENANCE AND ADJUSTMENT

6-31

9. Have a Yamaha dealer adjust the

headlight beam if necessary.

EAU24133

Replacing the tail/brake light
bulb

1. Remove the tail/brake light lens by

removing the screws.

2. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws.

NOTICE:

Do not over-

tighten the screws, otherwise
the lens may break.

[ECA10681]

EAU24212

Replacing a turn signal light
bulb

1. Remove the turn signal lens by re-

moving the screws.

2. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws.

NOTICE:

Do not over-

tighten the screws, otherwise
the lens may break.

[ECA10681]

1. Screw

U11CE4E0.book Page 31 Friday, December 3, 2010 9:12 AM

Summary of Contents for midnight star XVS1300A



























































































Search results

Summary of Contents for midnight star XVS1300A

Reviews:

Related manuals for midnight star XVS1300A

Brands by name

Popular brands

Yamaha midnight star XVS1300A, Owner'S Manual

Search results

Summary of Contents for midnight star XVS1300A

Reviews:

Related manuals for midnight star XVS1300A

Brands by name

Popular brands