background image

MG12XUK Owner’s Manual

4

PRECAUTIONS

PLEASE READ CAREFULLY 
BEFORE PROCEEDING 

Please keep this manual in a safe place for 
future reference.

 WARNING

Always follow the basic precautions listed below to 
avoid the possibility of serious injury or even death 
from electrical shock, short-circuiting, damages, fire or 
other hazards. These precautions include, but are not 
limited to, the following:

Power supply/AC power adaptor

• Do not place the power cord near heat sources such as 

heaters or radiators, and do not excessively bend or 
otherwise damage the cord, place heavy objects on it, or 
place it in a position where anyone could walk on, trip over, 
or roll anything over it.

• Only use the voltage specified as correct for the device. The 

required voltage is printed on the name plate of the device.

• Use the specified adaptor only. Using the wrong adaptor 

can result in damage to the device or overheating.

• Check the electric plug periodically and remove any dirt or 

dust which may have accumulated on it.

• When setting up the device, make sure that the AC outlet 

you are using is easily accessible. If some trouble or 
malfunction occurs, immediately turn off the power switch 
and disconnect the plug from the outlet. Even when the 
power switch is turned off, as long as the power cord is not 
unplugged from the wall AC outlet, the device will not be 
disconnected from the power source.

• Remove the electric plug from the outlet when the device is 

not to be used for extended periods of time, or during 
electrical storms.

Do not open

• This device contains no user-serviceable parts. Do not open 

the device or attempt to disassemble the internal parts or 
modify them in any way. If it should appear to be 
malfunctioning, discontinue use immediately and have it 
inspected by qualified Yamaha service personnel.

Water warning

• Do not expose the device to rain, use it near water or in 

damp or wet conditions, or place on it any containers (such 
as vases, bottles or glasses) containing liquids which might 
spill into any openings. If any liquid such as water seeps 
into the device, turn off the power immediately and unplug 
the power cord from the AC outlet. Then have the device 
inspected by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

Hearing loss

• Avoid setting all equalizer controls and faders to their 

maximum. Depending on the condition of the connected 
devices, doing so may result in feedback that can cause 
hearing loss and damage the speakers.

• Do not use headphones for a long period of time at a high or 

uncomfortable volume level, since this can cause 
permanent hearing loss. If you experience any hearing loss 
or ringing in the ears, consult a physician.

• Before connecting the device to other devices, turn off the 

power for all devices. Also, before turning the power of all 
devices on or off, make sure that all volume levels are set to 
the minimum. Failing to do so may result in hearing loss, 
electric shock, or device damage.

• When turning on the AC power in your audio system, always 

turn on the power amplifier LAST, to avoid hearing loss and 
speaker damage. When turning the power off, the power 
amplifier should be turned off FIRST for the same reason.

Fire warning

• Do not place any burning items or open flames near the 

device, since they may cause a fire.

If you notice any abnormality

• If any of the following problems occur, immediately turn off 

the power switch and disconnect the electric plug from the 
outlet.
- The power cord or plug becomes frayed or damaged.
- Unusual smells or smoke are emitted.
- Some object has been dropped into the device.
- There is a sudden loss of sound during use of the device.
- Cracks or other visible damage appear on the device.
Then have the device inspected or repaired by qualified 
Yamaha service personnel.

• If this device or the AC power adaptor should be dropped 

or damaged, immediately turn off the power switch, 
disconnect the electric plug from the outlet, and have the 
device inspected by qualified Yamaha service personnel.

 CAUTION

Always follow the basic precautions listed below to 
avoid the possibility of physical injury to you or others, 
or damage to the device or other property. These 
precautions include, but are not limited to, the 
following:

Power supply/AC power adaptor

• Do not cover or wrap the AC power adaptor with a cloth or 

blanket.

• When removing the electric plug from the device or an 

outlet, always hold the plug itself and not the cord. Pulling 
by the cord can damage it.

Location

• Do not place the device in an unstable position where it 

might accidentally fall over and cause injuries.

• Do not place the device in a location where it may come into 

contact with corrosive gases or salt air. Doing so may result 
in malfunction.

• Before moving the device, remove all connected cables.

Maintenance

• Remove the power plug from the AC outlet when cleaning 

the device.

PA_en_8  1/2

Summary of Contents for MG12XUK





























Reviews: