M7CL Owner’s Manual
Troubleshooting
292
Can’t save to USB storage device
❍
Is the USB storage device protected?
❍
Does the USB storage device have enough free capacity to save the data?
❍
When formatting the USB storage device, format it in FAT32 or FAT16 format.
Can’t change the patching in AVS-
ESMonitor
❍
Could the AUTO CONFIGURE button for the Stage Box Setup function be turned on?
❍
Could dip switches 5–8 for the SB168-ES be set to On (down position)?
❍
Could the “Lock Routing” option be selected on the Control screen of AVS-ESMonitor?
Can’t change Serial Communication
Mode in AVS-ESMonitor
❍
Could the AUTO CONFIGURE button for the Stage Box Setup function be turned on?
❍
Could dip switches 5–8 for the SB168-ES be set to On (down position)?
Can’t execute Quick Setup in AVS-
ESMonitor
❍
Could the AUTO CONFIGURE button for the Stage Box Setup function be turned on?
❍
Could dip switches 5–8 for the SB168-ES be set to On (down position)?
Can’t transmit/receive MIDI data
❍
Is the MIDI PORT selected correctly? (
❍
Are the mode and channel selected correctly on the transmitting and receiving devices? (
❍
Has an event been assigned for the program change? (
When you recall a scene, some
channels/parameters are not updated
❍
Could Recall Safe have been applied to that channel or parameter? (
❍
Could FOCUS for the recalled scene be turned off? (
❍
Could user level restrictions have been specified? (
You turn on a CUE button in the EFFECT
screen, but it is automatically defeated
❍
This is defeated automatically when you switch screens in the display. (
When you recall a scene, it takes a
certain amount of time for the faders to
stop
❍
Could you have specified a fade time? (
The panel LEDs or LCD display are too
dark / too bright
❍
This can be adjusted in the SETUP screen. (
Signal level of a specific frequency is
low
❍
Could the EQ gain be turned down excessively?
❍
Routing a signal through a GEQ or effect will delay it relative to other signals. If this signal is mixed with
the signal via a different signal path, a comb filtering effect will cause the level of a specific frequency
to be decreased.
Can’t control an external head amp
(AD8HR)
❍
Is the external head amp connected to the REMOTE connector?
❍
Is the audio output signal of the external head amp being input via an I/O card to SLOT 1–3?
❍
Is the input port of the external head amp set correctly?
❍
Could there be a problem with the cable that connects the M7CL and external head amp? Are you
using a D-sub 9-pin cross cable?
Can’t control the M7CL by M7CL V3
Editor.
❍
Is the M7CL firmware version 3?
❍
Are you using M7CL V3 Editor as an editor?
❍
Refer to M7CL V3 Editor installation guide on our web site.
http://www.yamahaproaudio.com/
In the LCD display, there are some
black points (unlit) or white points
(always lit).
❍
Unfortunately, this is a common characteristic of TFT-LCDs and not a malfunction.
Summary of Contents for M7CL StageMix V1.5
