background image

 

Operation

 

36

 

EMU27450

 

Operating engine

 

EMU27480

 

Feeding fuel

WARNING

 

EWM00420 

 

 

Before starting the engine, make sure
that the boat is tightly moored and that
you can steer clear of any obstructions.
Be sure there are no swimmers in the
water near you.

 

 

When the air vent screw is loosened,
gasoline vapor will be released. Gaso-
line is highly flammable, and its vapors
are flammable and explosive. Refrain
from smoking, and keep away from
open flames and sparks while loosen-
ing the air vent screw.

 

 

This product emits exhaust gases
which contain carbon monoxide, a col-
orless, odorless gas which could cause
brain damage or death when inhaled.
Symptoms include nausea, dizziness,
and drowsiness. Keep cockpit and cab-
in areas well ventilated. Avoid blocking

 

exhaust outlets.

 

1.

If there is an air vent screw on the fuel
tank cap, loosen it 2 or 3 turns.

2.

If there is a fuel joint or a fuel cock on the
boat, firmly connect the fuel line to the
joint or open the fuel cock.

3.

Squeeze the primer pump with the outlet
end up until you feel it become firm.

 

EMU27490

 

Starting engine

 

EMU27624

 

Electric start and remote control models

 

1.

Place the remote control lever in “ ”
(neutral).

NOTE:

 

The start-in-gear protection device prevents
the engine from starting except when in neu-

 

tral.

2.

Attach the engine stop switch lanyard to

N

ZMU04588

✩✱✣✬✤✧✲✣ ✦✩   

©

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for LZ250
























































































Reviews: