Yamaha LX150A Page 42 Owner'S Manual Download

Page: 42 / 125

2-19

EMU00163

TOP COWLING LOCK LEVERS

To remove the engine top cowling, pull
up the front and rear lock levers. Then lift
off the cowling. When replacing the cowl-
ing, check to be sure it fits properly in the
rubber seal. Then lock the cowling again
by moving the levers downward.

301021

301022

EMU00157

TILT SUPPORT LEVER

To keep the outboard motor in the tilted-
up position, lock the tilt support lever to
the clamp bracket.

403033

000825

EMU01146

FLUSHING DEVICE

This device

is used to clean the cooling

water passages of the motor using a gar-
den hose and tap water.

NOTE:

Refer to “Cleaning Cooling-water
Passages” in Chapter 4 for instructions on
usage.

67K-9-13-2 4/19/01 10:44 AM Page 20

Summary of Contents for LX150A






























































































































Search results

Summary of Contents for LX150A

Reviews:

Related manuals for LX150A

Brands by name

Popular brands

Yamaha LX150A, Owner'S Manual

Search results

Summary of Contents for LX150A

Reviews:

Related manuals for LX150A

Brands by name

Popular brands