Yamaha LX150A Owner'S Manual Download Page 103

Page: 103 / 125

5-4

Trouble

Possible Cause

Remedy

16. Thermostat faulty or clogged.

17. Air vent screw closed.

18. Fuel pump damaged.

19. Fuel joint connection incorrect.

20. Heat range of spark plug incorrect.

21. Engine not responding properly to

shift lever position.

16. Have serviced by a Yamaha

dealer.

17. Open the air vent screw.

18. Have serviced by a Yamaha

dealer.

19. Connect correctly.

20. Inspect spark plug and replace it

with recommended type.

21. Have serviced by a Yamaha

dealer.

E. Engine power loss.

F. Engine vibrates

excessively.

1. Propeller damaged.

2. Propeller shaft damaged.

3. Weeds or other foreign matter

tangled on propeller.

4. Motor mounting bolt loose.

5. Steering pivot loose or damaged.

1. Have propeller repaired or

replaced.

2. Have serviced by a Yamaha

dealer.

3. Remove and clean propeller.

4. Tighten bolt.

5. Tighten or have serviced by a

Yamaha dealer.

67K-9-13-5 4/19/01 10:41 AM Page 5

Summary of Contents for LX150A






























































































































Search results

Summary of Contents for LX150A

Reviews:

Yamaha LX150A, Owner'S Manual, Page: 103 / 125

Search results

Summary of Contents for LX150A

Reviews: