Yamaha LF115 Owner'S Manual Download Page 79 | Manualshive

Page: 79 / 116

background image

Operation

73

3.

Pull the tilt support lever toward you to
support the engine.

WARNING! After

tilting the outboard motor, be sure to
support it with the tilt support knob or
tilt support lever. Otherwise the out-
board motor could fall back down
suddenly if oil in the power trim and tilt
unit or in the power tilt unit loses pres-

sure.

[EWM00263]

NOTICE:

Do not use the

tilt support lever or knob when traile-
ring the boat. The outboard motor
could shake loose from the tilt support
and fall. If the motor cannot be
trailered in the normal running posi-
tion, use an additional support device
to secure it in the tilt position. For
more detailed information, see page
76.

[ECM01642]

EMU42702

Procedure for tilting down

1.

Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support lever
becomes free.

2.

Release the tilt support lever.

1. Power trim and tilt switch

1. Power trim and tilt switch

1. Power trim and tilt switch

ZMU07850

UP

1

1

UP

ZMU08096

1. Tilt support lever

1. Tilt support lever

1

ZMU08097

1

ZMU08099

U6EK30E0.book Page 73 Wednesday, January 29, 2014 4:03 PM

«
...
77
78
79
80
81
...
»

Summary of Contents for LF115





















































































































Reviews:

No comments

Related manuals for LF115

Brand: QDI Pages: 69

Brand: MSI Pages: 61

EZ-USB HX2LP CY4605

Brand: Cypress Pages: 2

Brand: Linear Technology Pages: 10

126791-HMC764LP6C

Brand: Analog Devices Pages: 18

tKINO-AL-E1-R10

Brand: IEI Technology Pages: 12

Brand: Gigabyte Pages: 44

Brand: ASROCK Pages: 4

Brand: Gigabyte Pages: 147

Brand: AOpen Pages: 125

Brand: MSI Pages: 98

Brand: Global American Pages: 31

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 105

Desktop Board D850EMD2

Brand: Intel Pages: 24

Brand: Abit Pages: 134

Brand: Biostar Pages: 98

A770 A2G PLUS - BIOS

Brand: Biostar Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands