Yamaha GRIZZLY 350 YFM35GZ Owner'S Manual Download Page 34 | Manualshive

Page: 34 / 138

Yamaha GRIZZLY 350 YFM35GZ Owner'S Manual Download Page 34

4-9

4

EBU18754

Fuel

Make sure there is sufficient gasoline in the tank.

WARNING

EWB02521

Gasoline and gasoline vapors are extremely
flammable. To avoid fires and explosions and
to reduce the risk of injury when refueling, fol-
low these instructions.

1. Before refueling, turn off the engine and be

sure that no one is sitting on the vehicle. Nev-
er refuel while smoking, or while in the vicinity

of sparks, open flames, or other sources of ig-
nition such as the pilot lights of water heaters
and clothes dryers.

2. Do not overfill the fuel tank. When refueling,

be sure to insert the pump nozzle into the fuel
tank filler hole. Stop filling when the fuel reach-
es the bottom of the filler tube. Because fuel
expands when it heats up, heat from the en-
gine or the sun can cause fuel to spill out of
the fuel tank.

1. Fuel tank cap

1. Maximum fuel level
2. Fuel tank filler tube

U5WH66E0.book Page 9 Thursday, June 18, 2009 10:41 AM

«
...
32
33
34
35
36
...
»

Summary of Contents for GRIZZLY 350 YFM35GZ











































































































































Reviews:

No comments