manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35GZ, Owner'S Manual, Page: 28 / 138

Share
Download
Yamaha GRIZZLY 350 YFM35GZ Owner'S Manual Download Page 28

4-3

4

EBU18022

Speedometer 

This speedometer is equipped with an odometer
and a tripmeter. The tripmeter can be reset to zero
with the reset knob. Use the tripmeter to estimate
how far you can ride on a tank of fuel before going
to reserve. This information will enable you to plan
fuel stops in the future.

EBU18061

Handlebar switches 

EBU18080

Engine stop switch “

/

” 

Set this switch to “

” before starting the engine.

The engine stop switch controls the ignition and
stops the engine when it is running. Use this switch
to stop the engine in an emergency situation. The
engine will not start or run when this switch is set
to “

”.

1. Reset knob

2. Speedometer
3. Odometer

4. Tripmeter

1. Light switch “

/

/OFF”

2. Engine stop switch “

/

”

3. Start switch “

”

4. Horn switch “

”

U5WH66E0.book  Page 3  Thursday, June 18, 2009  10:41 AM

Summary of Contents for GRIZZLY 350 YFM35GZ











































































































































Reviews:

No comments