Yamaha GRIZZLY 350 YFM35GZ Owner'S Manual Download Page 118

Page: 118 / 138

8-39

If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off all electrical

circuits.

NOTICE

ECB00640

To prevent accidental short-circuiting, turn off
the main switch when checking or replacing a
fuse.

2. Remove the blown fuse, and then install a

new fuse of the specified amperage.

WARNING! Always use a fuse of the spec-
ified rating, and never use a substitute ob-
ject in place of the proper fuse. An
improper fuse or a substitute object can
cause damage to the electrical system,
which could lead to a fire.

[EWB02172]

3. Turn the key to “ON” and turn on the electrical

circuits to check if the devices operate.

4. If the fuse immediately blows again, have a

Yamaha dealer check the electrical system.

1. Headlight fuse
2. Ignition fuse

3. Auxiliary DC jack fuse (for optional auxiliary DC jack)

4. Signaling system fuse
5. Spare fuse

Specified fuses:

Main fuse:

30.0 A

Headlight fuse:

15.0 A

Ignition fuse:

15.0 A

Signaling system fuse:

10.0 A

Auxiliary DC jack fuse:

10.0 A

U5WH66E0.book Page 39 Thursday, June 18, 2009 10:41 AM

Summary of Contents for GRIZZLY 350 YFM35GZ











































































































































Search results

Summary of Contents for GRIZZLY 350 YFM35GZ

Reviews:

Yamaha GRIZZLY 350 YFM35GZ, Owner'S Manual, Page: 118 / 138

Search results

Summary of Contents for GRIZZLY 350 YFM35GZ

Reviews: