Yamaha FZ6Y Owner'S Manual Download Page 76

Page: 76 / 106

PERIODIC MAINTENANCE AND ADJUSTMENT

7-33

2. If the battery will be stored for more

than two months, check it at least
once a month and fully charge it if
necessary.

3. Fully charge the battery before in-

stallation.

4. After installation, make sure that

the battery leads are properly con-
nected to the battery terminals.

NOTICE

ECA16530

Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.

EAU32843

Replacing the fuses

The main fuse is located under the fuel
tank. (See page 7-18.)

The fuse box is located behind panel C.
(See page 7-9.)

If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off

the electrical circuit in question.

2. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

WARNING! Do not

use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire.

[EWA15131]

1. Main fuse

2. Spare main fuse

1. Fuse box

1. Headlight fuse
2. Signaling system fuse

3. Ignition fuse

4. Radiator fan fuse
5. Backup fuse (for odometer and clock)

6. Fuel injection system fuse

7. Spare fuse
8. Taillight fuse

U4S812E0.book Page 33 Monday, October 6, 2008 4:06 PM

Summary of Contents for FZ6Y











































































































Search results

Summary of Contents for FZ6Y

Reviews:

Related manuals for FZ6Y

Brands by name

Popular brands

Yamaha FZ6Y, Owner'S Manual

Search results

Summary of Contents for FZ6Y

Reviews:

Related manuals for FZ6Y

Brands by name

Popular brands