Yamaha FZ6Y Owner'S Manual Download Page 22 | Manualshive

Page: 22 / 106

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-5

4

EAU42772

Engine trouble warning light “

”

This warning light comes on if a prob-
lem is detected in the electrical circuit
monitoring the engine. If this occurs,
have a Yamaha dealer check the self-
diagnosis system. (See page 4-8 for an
explanation of the self-diagnosis de-
vice.)
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. If the warning light does not come
on for a few seconds, then go off, have
a Yamaha dealer check the electrical
circuit.

EAU40179

Multi-function meter unit

WARNING

EWA12422

Be sure to stop the vehicle before
making any setting changes to the
multi-function meter unit. Changing
settings while riding can distract the
operator and increase the risk of an
accident.

The multi-function meter unit is
equipped with the following:

●

a speedometer

●

a tachometer

●

an odometer

●

two tripmeters (which show the
distance traveled since they were
last set to zero)

●

a fuel reserve tripmeter (which
shows the distance traveled since
the left segment of the fuel meter
started flashing)

●

a clock

●

a fuel meter

●

a coolant temperature display

●

an air intake temperature display

●

a self-diagnosis device

●

an LCD and tachometer bright-
ness control mode

TIP

●

Be sure to turn the key to “ON” be-
fore using the “SELECT” and “RE-
SET” buttons.

●

To switch the speedometer and
odometer/tripmeter displays be-
tween kilometers and miles, press
the “SELECT” button for at least
one second.

1. Coolant temperature display/air intake tem-

perature display

2. Speedometer

3. Tachometer
4. Odometer/tripmeter/fuel reserve tripmeter

5. “SELECT” button

6. “RESET” button
7. Clock

8. Fuel meter

U4S812E0.book Page 5 Monday, October 6, 2008 4:06 PM

«
...
20
21
22
23
24
...
»

Summary of Contents for FZ6Y











































































































Reviews:

No comments

Related manuals for FZ6Y

Brand: HYOSUNG Pages: 199

ALK.00.733.15000/B

Brand: SW-Motech Pages: 14

TRIUMPH Bonneville T 120

Brand: hepco & becker Pages: 4

Brand: Honda Pages: 61

Daytona 955i 2002

Brand: Triumph Pages: 384

Brand: GAS GAS Pages: 69

2006 G 650 Xmoto

Brand: BMW Pages: 132

Brand: Bajaj Pages: 39

Brand: MRA Pages: 6

Brand: CATU Pages: 6

Brand: CATU Pages: 8

Brand: DYNATEK Pages: 8

Brand: Surtek Pages: 12

Brand: Dayi Motor Pages: 18

Brand: Brixton Pages: 49

Brand: Wunderlich Pages: 5

Brand: Dräger Pages: 256

Brand: Aosom Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands