background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-7

7

18

Sidestand pivot

• Check operation.
• Apply lithium-soap-based grease 

lightly.

19

*

Sidestand switch

• Check operation and replace if 

necessary.

20

*

Front fork

• Check operation and for oil leak-

age.

• Replace if necessary.

21

*

Shock absorber as-
sembly

• Check operation and for oil leak-

age.

• Replace if necessary.

22

Engine oil

• Change (warm engine before 

draining).

23

*

Engine oil filter car-
tridge

• Replace.

24

*

Cooling system

• Check hoses for cracks or dam-

age.

• Replace if necessary.

• Change coolant.

25

*

Front and rear brake 
switches

• Check operation.

26

*

Control cables

• Apply Yamaha chain and cable 

lube or engine oil thoroughly.

No.

ITEM

ROUTINE

INITIAL

ODOMETER READINGS

600 mi 

(1000 km) 

or 

1 month

4000 mi 

(7000 km) 

or 

6 months

8000 mi 

(13000 km) 

or 

12 months

12000 mi 

(19000 km) 

or 

18 months

16000 mi 

(25000 km) 

or 

24 months

20000 mi 

(31000 km) 

or 

30 months

U36P14E0.book  Page 7  Thursday, August 2, 2012  2:13 PM

Summary of Contents for FZ6RD(C)























































































































Reviews: